Laboratory Services

Guide to Using Services at the Qom University of Technology Central Laboratory:

1. Email the laboratory service request form and any documentation regarding fee discounts to centrallab@qut.ac.ir.
2. Deliver the sample(s) to the Qom University of Technology Central Laboratory (samples may also be sent via postal service).
3. Deposit the required service fee into the Central Laboratory's dedicated account and email a clear, legible image of the payment receipt to centrallab@qut.ac.ir.
To make the payment—after determining the final amount based on the service type and number of units as per the table below—click on the "Proceed to Electronic Payment Page" link.
4. The test results will be emailed to the requester.

Important Notes:

Requests submitted by universities and scientific centers affiliated with the Ministry of Science (within the country's Research Region 4) are eligible for a 25% discount (a formal letter of introduction from the head of the originating university/center's central laboratory is required to avail of this discount).
Test results are retained for a maximum of two months following sample submission; once deleted, the results cannot be re-sent.
If services are provided outside of standard working days or hours, a surcharge equivalent to 20% of the equipment service fee will be added to the final cost.

Note: By clicking on the title of each device in the corresponding column, the device image will be displayed .

Service code	Device/Test/Service Name	Service Description	Service unit	Service fee (Toman)	Description
1	60 ton concrete beam flexural strength jack [ Flexural Testing Jack ]	Performing flexural strength tests on unreinforced concrete beams and determining the modulus of rupture of concrete ( determining the tensile strength of concrete in bending )	Sample	290,000
2	Concrete Breaker Jack 2000 kN [ Concrete Breaker Jack ]	Generation of stress-strain curve of concrete under pressure (determination of compressive strength of concrete)	Sample	240,000
3	8- meter tilting research flume [ Multipurpose Tilting Flume ]	Analysis of fluid parameters in terms of fluid channel slope variables and inlet fluid volume	Clock	480,000
4	Guillotine [ Hydraulic Guillotine ] Hydraulic Guillotine	Cutting metal sheets up to 2 mm thick and up to 2 meters wide (electric)	Sample	50,000 75,000	Up to a maximum width of 0.5 meters Up to a maximum width of 1 meter
5	Sheet Metal Bending Machine	Bending metal sheets up to 2 mm thick up to 2 meters wide (manual)	Clock	240,000
6	phase MIG/MAG welding machine [ Tungsten Inert Gas Welding Machine ]	Welding services	Clock	480,000 720,000 480,000 600,000	MIG without argon gas cost MIG with argon gas cost MAG without CO2 gas cost MAG with CO2 gas cost [ The amounts are 100 thousand Tomans per hour, including the operator's fee .]
7	TiG welding inverter [ Gas Metal Arc Welding Machine ]	Welding services	Clock	480,000 720,000	No cost for argon gas With the cost of argon gas [ The amount, including the operator's fee, is 100 thousand Tomans per hour .]
8	Spot Welding Machine 50 kVA up to 3 mil thickness [ Spot Welding Machine ]	Welding services	Clock	360,000
9	Lathe Machine	Turning metal shafts	Clock	720,000 600,000	With steel material, with aluminum or brass material [ The amount, including the operator's fee, is 100 thousand Tomans per hour .]
10	CNC Milling Machine	CNC milling services	Clock	720,000 600,000	With steel material, with aluminum or brass material [ The amount, including the operator's fee, is 100 thousand tomans per hour .]
11	30 ton hot press [ Hot Press ]	Compression molding for polymer samples	Clock	450,000	Minimum service time 2 hours
12	30 ton cold press [ Hydraulic Press ] Hydraulic Press	Compression molding for polymer samples	Clock	450,000	Simultaneously with hot press
13	Metal tensile testing up to 25 tons [ General mechanical properties testing machine ] Universal Testing Machine	Conducting tensile strength tests for metal samples	Sample	1,000,000
14	Tensile, bending, compression testing (plastic and rubber) [ General mechanical properties testing machine ] Universal Testing Machine	Conducting tensile, bending and compressive strength tests for polymer samples	Sample	450,000	Less than an hour
15	Differential Scanning Calorimeter ( DSC )	Investigating the thermal behavior of polymer samples	Sample	1,500,000	Up to 1 hour in the air atmosphere ( cost of each additional hour is 100,000 Tomans )
16	Thermogravimetric Analysis TGA [ Simultaneous Thermal Analyzer ]	Investigating the thermal stability of polymer samples	Sample	1,500,000	Up to 1 hour in the air atmosphere ( cost of each additional hour is 100,000 Tomans )
17	Ultraviolet Visible Spectrometer [ Ultraviolet Visible Spectrometer ] Ultraviolet Visible Spectrometer	Spectroscopy in the visible and ultraviolet wavelength range	Sample	200,000	Transmitted, absorbed, and reflected modes
18	Rubber Curing Rheometer Test [ Moving Die Rheometer ]	Study of the curing behavior of rubber compounds	Sample	1,000,000 1,700,000 2,500,000	Up to 20 minutes Up to 30 minutes Up to 60 minutes
19	Internal Mixer	Preparation of polymer blends	Clock	1,500,000	Minimum service time 2 hours
20	Laboratory Twin Screw Extruder [ Twin Screw Extruder ]	Preparation of masterbatches and polymer blends	Clock	1,500,000	Minimum service time 2 hours
21	Centrifuge 14 thousand revolutions [ Centrifuge ]	Separation of components of mixed samples	Clock	750,000	Up to 14,000 rpm
22	Electric furnace [ Box furnace ] Box Furnace	heating processes	Clock	400,000	Maximum temperature 1000 degrees Celsius
23	Vacuum Oven	Drying	Clock	350,000	Minimum service time 2 hours
24	Professional Scanning Probe Microscope [ Scanning Probe Microscope ] Scanning Probe Microscope	AFM analysis	Clock	-
25	Optical Microscope (Transmitted/Reflected) [ Optical Microscope ]	Optical imaging	Clock	700,000
26	Electrospinning [ electrospinning machine ] Electrospinning	Nanofiber production	Clock	750,000	Minimum service time 2 hours
27	Conventional oven [ oven ] Oven	Drying	Clock	100,000	Minimum service time 2 hours
28	Homogenizer (high speed mixer) [ homogenizer ]	Homogenization of liquids	30 minutes	1,100,000
29	Rotary Vacuum Distillation Machine [ Rotary Evaporator ] Rotary Evaporator	Separation of volatile components from solutions	Clock	120,000
30	Shoof Balon [ Shoof Balon ] Electromantle	Multi-channel heating	Clock	200,000
31	Magnetic-thermal stirrer (hotplate with magnetic stirrer ) [ Hotplate and magnetic stirrer ] Magnetic Stirring Hotplate	Heating and mixing	Clock	150,000
32	Mechanical Stirrer	Mixing	Clock	300,000
33	Melt Flow Index Tester	MFI measurement	3 to 5 times	1,000,000	The desired sample must be delivered to the laboratory in the form of powder, granules, or flakes .
34	Impact testing machine [ Izod and Charpy impact testing machine ] Izod & Charpy Impact Testing	Determining the fracture strength of samples	Sample	100,000
35	Hardness tester (plastics and rubber) [ Shore A & D Hardness Tester ]	Determining the hardness of objects	3 to 5 times	200,000
36	Ultrasonic bath probe [ Ultrasonic homogenizer ]	Homogenization	Clock	650,000
37	Three Dimensional Printer	3D printing services	Filament (hours) Resin (hours)	450,000 220,000	include the cost of filament and resin .
38	Thermal camera [ Infrared camera ] Infrared Camera	Thermal imaging	Clock	240,000
39	Hartmann High-Speed Hyperspectral Camera [ Hyperspectral Imaging Camera ]	Hyperspectral imaging in the visible and near-infrared (VNIR) range (400 to 2500 nm )	Watch sample	120,000 480,000
40	Power Analyzer [ Power Quality Measuring Device ] Power Quality Analyzer	Display and record electrical parameters of power systems in transient and steady state	Clock	480,000
41	Digital Oscilloscope 100 MHz 4 Channels 1 GSa /s [ Digital Oscilloscope ] Digital Oscilloscope	Display and store voltage waveforms through 4 channels with a sampling frequency of 1 gigasample/s	Clock	120,000
42	Combustion Gas Analyzer [ Combustion Gas Measuring Device ]	Determining the amount of gases produced by combustion	Clock	480,000
43	Vertical injection machine	Shaping plastic materials	Clock	1,000,000
44	Roller machine	Compounding of tires	Clock	500,000
45	Abrasion testing machine	Testing the abrasion resistance of rubbers	Clock	500,000
46	Rebound testing machine	Checking the resilience of rubbers	Clock	350,000
47	Fatigue testing machine	Checking the level of rubber fatigue	Clock	600,000
48	Metal tensile testing up to 100 tons [ General mechanical properties testing machine ] Universal Testing Machine	Conducting tensile strength tests for metal samples	Sample	3,000,000
49	Workbench with general polymer laboratory equipment		Week	1,000,000

To enter the payment section, click on the following phrase :

" Transfer to electronic payment page "